Forum Post: Altium Import into Allegro 17.40 Problem
Folks, I have imported Altium ASCII projects into Allegro before without too much issue. However, this time, it is taking a huge a mount of time and never finishes, but gets stuck on 1-out-of-364...
View ArticleForum Post: removing layers
hello is there a way to remove a layer even if there r some objects on the layer? it takes me a whole day to delete objects so i just simply would like to delete the layers with objects attached....
View ArticleForum Post: Issue with Signal naming in design entry HDL
Hi, I am working on a hierarchical design ,in the subblock i am trying to name the signals names of the Devicefrom place signal name -->entering all the names but it should be coming serially in the...
View ArticleForum Post: Need help regarding Differential Pair Routing on PCB Editor 17.4
Hi I'm a newbie, I need suggestions regarding differential pair I have completed most of my routing on a 4 layer board and not routed the differential pair which I had kept it later to route, but now...
View ArticleForum Post: RE: How to import the Design Entry DHL schematic Design to OrCAD...
Hi Rohit, For points #1 and #2 , I believe the answer is YES. However, you may need to reach out to Elgris Team directly for further clarification. Regarding point #3 , the process involves converting...
View ArticleForum Post: RE: Altium Import into Allegro 17.40 Problem
Can you share the error code or log file to check the issue?
View ArticleForum Post: RE: Altium Import into Allegro 17.40 Problem
Hi, I do not get an "error code" or "log file" as the process never gets that far before the entire Allegro import process locks up completely. The only way to stop the Allegro "freeze" is to go to the...
View ArticleForum Post: Cadence Reality/ 6sigmaRoom Thermal modelling Error
Hello all, apologies if this is the wrong forum, I searched "Data Centre" and it lead here. Also apologies for occasionally using old Software names, still learning which package is now called what. If...
View ArticleForum Post: RE: removing layers
We cannot delete a layer if there are objects present on that specific layer. The tool does not allow that and it lists the objects and their location that are present on the layer which are preventing...
View ArticleForum Post: Sampled HB noise analysis: Output noise to Edge phase noise...
Hello, I have a very simple test case as below. In a Vsource sinusoidal element, flat phase noise of -160dBc/Hz is specified. It is converted to differential waveform of 2V pk and phase noise is...
View ArticleForum Post: RE: Need help regarding Differential Pair Routing on PCB Editor 17.4
Hi, That seems to be a tricky situation. If it were me, I would: 1. Perform some routing cleanups in the areas where the differential pairs need to be routed. 2. Create constraints in Constraint...
View ArticleForum Post: RE: Need help regarding Differential Pair Routing on PCB Editor 17.4
Thank you so much Gowtham Will look into it
View ArticleForum Post: RE: Issue with Signal naming in design entry HDL
Hi SIVAREDDY TI , I need some more data to help you with this requirement. I will be contacting you through another channel for this.
View ArticleForum Post: RE: Need help regarding Differential Pair Routing on PCB Editor 17.4
Hi, if you are out of routing space and time is not on your side just move that 4lyr board to 6lyrs instead. There will be a minor cost incursion in volume for a 6lyr board, however from an electrical...
View ArticleForum Post: RE: Need help regarding Differential Pair Routing on PCB Editor 17.4
Thank you so much excellon1 Will ask the fabricator for the later stack up with respect to 6 layer
View ArticleForum Post: RE: Create Menu/Window with TCL to fill a user defined Title...
sir, Could you give me some advice, if you can, please teach me, I want to learn more, please!
View ArticleForum Post: RE: How to extract libraries from a schematic?
One alternative to archiving the design is to manually extract the parts used in the design and create a custom library. Many design tools allow you to export parts or symbols from the design files....
View ArticleForum Post: Creating BOM (Bill Of Materials) Report from the PCB Editor only...
Dear Community, I have designed a PCB board and would like to generate a Bill of Materials (BOM) report from the PCB Editor . However, my requirement is to create the report specifically for the...
View ArticleForum Post: RE: How to import the Design Entry DHL schematic Design to OrCAD...
Hai Gowtham, Thanks for the response
View ArticleForum Post: RE: Creating BOM (Bill Of Materials) Report from the PCB Editor...
Hi, Generate your report or export the placement, save out the report to disk. Within the report you should see a field called SYM_MIRROR. This field determines if a component is on the top of the...
View Article