Forum Post: RE: Orcad/Allegro 17.2 HOTFIX S049 - .env file issues. Some...
I think most of this is related to the new command window that was introduced. You can go and use the old one if you want until these issues are resolved. It is found in User Preferences - ui - general...
View ArticleForum Post: Device spacing in modgen using SKILL
Can anyone help me in finding out how to set custom device spacing in a modgen using SKILL. I've gone through ciConCreate() in the documentation and can create a modgen using it, but couldn't find any...
View ArticleForum Post: Simulation set up for Image rejection ratio of IQ Down converter...
Hi There, I'm looking to simulate Image rejection ratio of down converter IQ current mode passive mixer. In " Spectre Circuit Simulator and Accelerated Parallel Simulator RF Analysis in ADEExplorer...
View ArticleForum Post: RE: Image Rejection of IQ mixer
Hi itos, Did you get any luch with simulation set up of Image rejection of Down converter IQ Mixer ? Could please share steps to set up test bench for it ? Warm Regards, Girish W
View ArticleForum Post: RE: Orcad/Allegro 17.2 HOTFIX S049 - .env file issues. Some...
Hi Steve, Looks like you are right on that. In my case disabling the " ui - general and uncheck enable_command_window_history" was the fix for me. All the best Paul.
View ArticleForum Post: RE: How to identify the duplicate refdes in OrCAD Capture 17.2...
Orcad Capture has never dynamically kept track of refdez so it does not know if a duplicate refdes exists in the design until after the fact. There is an easy way to find duplicates. Just run the Find...
View ArticleForum Post: N_12_LLRF (UMC90nm library) Long channel pinchoff saturation
Hello , i Have the N_12_LLRF component from UMC90nm Library my L=90nm what gate_finger_width to use in order to get this component to be characterised as long channel component? (so i will get a good...
View ArticleForum Post: RE: Capture 17.2 can't close Property Editor window with keyboard
I also found this problem in 17.2 hotfix049
View ArticleForum Post: Missing Parameter in Layout "Edit Instance Properties"
Hi Guys, I can't change the size of pmos or nmos during Layout. In my Layout " Edit Instance Properties ", i don't see any " width " parameter. Literally that does not allow me to use virtuoso for...
View ArticleForum Post: help me with you ..
[Notebook] Windows 10 - When I power down PC / Notebook, USB ports continue to work. How do they stop working?.. .
View ArticleForum Post: RE: Missing Parameter in Layout "Edit Instance Properties"
Those warnings in the CIW are nothing to do with this - it's because you have some old ADE-related cdsenv settings in a central cdsenv in the NCSU CDK - but they are for setting up the ADE plotting...
View ArticleForum Post: RE: Capture 17.2 can't close Property Editor window with keyboard
You'll need to report this to Cadence support ( http://support.cadence.com) or your Channel Partner (who you bought the software from) to get this looked at.
View ArticleForum Post: RE: Ignore component in the netlist
Thanks, I fixed the problem. I use NETLIST IGNORE property. I discovered also BOM_ IGNORE.
View ArticleForum Post: RE: Cadence Liberate Characterization Help
Thanks for pointing this out. Yes as you said, the current output depends on the previous clock edge (neg or pos) and the corresponding captured data. So that we should have different prevectors for...
View ArticleForum Post: RE: Cadence Liberate Characterization Help
Hi, The syntax of prevectors looks fine, as long as the states/sequence is correct/expected behavior. vector has have R/F for pin/related_pin. The order must be same as pinlist in define_cell. But you...
View ArticleForum Post: Filtering data to plot for nested sweeps
Hi Everyone, I've run nested sweeps in spectre and I would like to filter the data, what I postprocess and plot with OCEAN. Let's say I want to plot the results with a fixed value of the second sweep,...
View ArticleForum Post: RE: Filtering data to plot for nested sweeps
Update: I can add value() the argument of the sweep parameter. I missed it, because I assumed that I have to state the sweep analysis name. User error. I am one step closer, though I do not know yet,...
View ArticleForum Post: The line width in the new version of Part Editor is not displayed...
For example, the line width I set in the Part Editor feels good, but when I update it to the schematic, it becomes very thick , as shown in the picture below. This problem is not found in the old...
View ArticleForum Post: RE: The line width in the new version of Part Editor is not...
This seems to be working correctly for me. I guess that you have tried deleting and redrawing the line with the issue? If the problem persists, you will need to get the library data to Cadence for...
View Article