Forum Post: RE: How to define measurement statements to get simulation output...
To define measurement statements and obtain simulation output results in a textual format using Allegro PSpice Simulator, you use the .MEAS (or .MEASURE ) command. This command allows you to define...
View ArticleForum Post: RE: Allegro X Capture 23.10.006 causes Mouse to Jump to Top or...
Can you please try with Version 24.1 along with hotfix 3 and let me know if you are facing the same issue.
View ArticleForum Post: Facing "Segmentation Fault" error while trying to run Assura DRC...
I am facing "Segmentation Fault" error. I am trying to run DRC using Assura for layout analysis in Cadence Virtuoso. Though I have attached the appropriate technology file and completed other steps...
View ArticleForum Post: RE: How to create a Verilog-a cell view from scratch
Using deNewCellView would open an interactive window - if that's what you want, then you need to use "text.veriloga" as the viewType: deNewCellView("opamp090" "testva2" "veriloga" "text.veriloga") If...
View ArticleForum Post: RE: Facing "Segmentation Fault" error while trying to run Assura...
Not enough information to go on (no info on versions used; I'd expect there to be some detailed log with more information). Please contact customer support. Andrew
View ArticleForum Post: RE: Facing "Segmentation Fault" error while trying to run Assura...
What version of Assura? What version of Virtuoso? Submitted from the gui? OA db or gds for the layout? N.B. The question clearly does not contain enough information to get close to the cause of the issue.
View ArticleForum Post: How to implement the SimVision Expression Calculator with tcl
Hi. I am using SimVision for Analog-Mixed Signal (AMS) simulations. Within SimVision, I have probed certain signals, such as currents, for analysis. To calculate the range average of these signals...
View ArticleForum Post: What format should we use for ordering PCBs from Fabricators?
The first IPC2581 board was fabricated in 2013; the odb format is popular among DFM Engineers; and Gerber has been familiar to PCB Fabricators since the 1980s. So have we moved on? Let's poll to...
View ArticleForum Post: RE: Allegro X Capture 23.10.006 causes Mouse to Jump to Top or...
Hi cstocci52 and Jeet , I tried disabling the "Grid References" under view but it did not solve the problem for me. However, I'm only facing this during Zoom-In. No issues during Zoom-Out, the cursor...
View ArticleForum Post: Cannot annotate DC operating point of a MonteCarlo version of a...
Good afternoon everyone, I searched through the forum and opened a lot of discussions, but I am not really sure the problem I am facing is the same than the others, so I am posting my own thread....
View ArticleForum Post: How to count the number of times an instance appears in a layout
I have a layout with 10s of 1000s of instances and I would like to write a script that reports, for each instance found in the layout, the number of times that instance appears. I have a script that...
View ArticleForum Post: Bind Double Press Escape to geDeselectAllFig not effect
Hi, I am trying to bind if I double press escape in Virtuoso Layout Editor XL, deselect everything (Default is Ctrl+D) So I wrote the following code and execute in CIW hiSetBindKey("Layout" "...
View ArticleForum Post: RE: How do I install and configure the License AWR - University...
Is your issue solved yet? I am having the same issue. The pop-up window disappearing after a couple of seconds without the license even properly being downloaded.
View ArticleForum Post: RE: Quick Align Pointer
Hi Andrew, Example for this simple script: procedure(printLayer() gs = geGetObjectSelectedSet()~>layerName printf("=> %L\n" gs) ) hiSetBindKey("Layout" "None " " print Layer ()...
View ArticleForum Post: Taking too long to load step files in 3D environment
Hello, When I click "Browse" to load STEP files from either my local drive or a shared network drive , it takes an unusually long time to respond and list files. Similarly, saving file also results in...
View ArticleForum Post: RE: How to make TitleBlock display the value of property...
Hi Moragn, I have a suggestion here that you can read the value from the .xml file that create when you set the value from Option-->Design Template-->Tile Block. I hope it helps to achieve your...
View ArticleForum Post: RE: How to expand/contract multiple voids at the same time?
Hi Judeeeee ! You can refer to it. It works with dynamic shapes only. Best regards, HoangKhoi ;+++++++++++++++++++++++++++++++++++++++++++++++++++++++++ axlCmdRegister("expand_void_shape"...
View ArticleForum Post: How to assigning Color to a subject [Allegro free physical viewer...
Hi all, Does anyone know How to assigning Color to a subject ? Not nets, I knew nets can be assigned a color. I am using [Allegro free physical viewer 24.1] Thank you very much.
View ArticleForum Post: RE: What format should we use for ordering PCBs from Fabricators?
We go with Gerber (+ excellon drill file + routing cutout file + master drawing: without them, no pcb): - Robust and universally accepted so no need to change. - Viewers show EXACLTY what we will get....
View Article