Forum Post: RE: Differential Pair Measurement
Thank you, I will try this, it makes sense. No need to apologize, you were not overlooking my issue, further more, you took time to help me out. Thanks again.
View ArticleForum Post: Create an array of variables using an array of vdc instances
in the case of using Schematic editor for creating a testbench and ADE Explorer/Assembler for simulating it, I was thinking how can I make my simulations easier when I have to check a variety of input...
View ArticleForum Post: RE: Will RHEL 8 work with IC6.1.8
Hi wgtkan IC618 is not officially supported on RHEL8 for now but it should work. You can refer to COS article 20444702 for more details on some of the related issues. Best regards Quek
View ArticleForum Post: RE: Create an array of variables using an array of vdc instances
Dear jdimov, [quote userid="362930" url="~/cadence_technology_forums/f/mixed-signal-design/47008/create-an-array-of-variables-using-an-array-of-vdc-instances"]At this point what would be very neat is...
View ArticleForum Post: RE: Create an array of variables using an array of vdc instances
Dear jdimov, [quote userid="362930" url="~/cadence_technology_forums/f/mixed-signal-design/47008/create-an-array-of-variables-using-an-array-of-vdc-instances"]At this point what would be very neat is...
View ArticleForum Post: (Multi-modulus) divider phase noise simulation
Hello everyone, Sorry if I missed the topic and the question is already answered. I want to simulate the phase noise contribution of an MMD used in a frequency synthesizer. For the purpose of...
View ArticleForum Post: RE: How to Describe Branch Current with Bsource
Are you sure that the curly braces are legal syntax? You can get some more information by typing spectre -h bsource at the Linux prompt. I didn't see any curly braces in these examples.
View ArticleForum Post: RE: How to model bidir switch in RNM
How about the Rapid Adoption Kit Bidirectional WREAL Switch Modeling using $SIE_input Based SV-RNM Transmission Gate ?
View ArticleForum Post: RE: Create an array of variables using an array of vdc instances
Hi ShawnLogan and thanks for a detailed reply. I think I understood your ADC but I am not it corresponds to my question so I'll try to explain it more. My question is more discussion based. For a...
View ArticleForum Post: DRC error after EMI shield placement
I am still learning here so, please be patience with me. I had no DRC errors until I placed the EMI shield. I believe the issue is related to the height of the shield. I did not create this component...
View ArticleForum Post: RE: DRC error after EMI shield placement
The shield will more than likely have a shape on PLACE_BOUND_TOP or _BOTTOM so try Setup - Areas - Package Height (or Outline - Package Height if you have an OrCAD License) then select the shape and...
View ArticleForum Post: Schematic net highlighting control
In the schematic display options form there are 3 controls for fine tuning net highlighting - Dynamic Highlighting (on/off), Dynamic Net Highlighting (on/off) and Connect by Name Highlighting (on/off)....
View ArticleForum Post: RE: Schematic net highlighting control
Hi, I think the setting you need is: envSetVal("schematic" "schDynamicNetHilightNoIslands" 'boolean t) (or possibly the 'nil' setting?) Best regards, Lawrence.
View ArticleForum Post: RE: Schematic net highlighting control
OK - let me be the first to call me a dope. When I tried the schDynamicNetHilightNoIslands command I had it set to nil and was getting all the highlighting lines between the names. I needed to set it...
View ArticleForum Post: RE: How can I suppress this warning
Sorry to state the obvious but you will need to fix the syntax/parsing errors...
View ArticleForum Post: RE: DRC error after EMI shield placement
That corrected the issue. Thank you for the advice.
View ArticleForum Post: RE: Orcad Capture Smart Pdf Pin Number Issue
Nice post. I learn something totally new and challenging on websites I stumbleupon on a daily basis. Thanking you aostv mod
View ArticleForum Post: RE: FlexId and Windows 10 May 2020 Update (v 2004)
Hi, it seems that I have the same issue with my new computer. Have you find a solution since your last post ? Best regards,
View ArticleForum Post: RE: same schematic and analysis - different results?
Hi Joris, did that issue got resolved? Actually I am also facing the same problem.
View ArticleForum Post: 180-degree phase shifter shows -90 degree in the graph measurement
Hello, I am testing a simple high-pass/low-pass phase shifter using lumped elements in AWRDE/Microwave Office. The 90-degree shifter looks about right, but the 180-degree shifter shows -90 degrees...
View Article