Forum Post: Not able to start XRUN (Error: No such file or directory)
Hello, I have the problem that I cannot start XRUN. I am doing the following steps to start the tool: source cadence_license_server source XCELIUM_23.03.007_RHELx86.sh xrun After these steps I get the...
View ArticleForum Post: RE: Best uses of TCL scripting
invincibleTechi Thanks for your feedback. What kind of task/automation you are doing using tcl scripting?
View ArticleForum Post: RE: Best uses of TCL scripting
my friends take tcl to do some works as follow check power source is missing extract old design content to create CIS library Make the design more formal to meet the company's requirements Output the...
View ArticleForum Post: RE: Not able to start XRUN (Error: No such file or directory)
Hi Max, The solution presented in the following article may solve this: Running xrun / xrun -64bit, SimVision, and Specman commands gives "Command not found" and " No such file or directory " errors on...
View ArticleForum Post: RE: Best uses of TCL scripting
@CadAP yes there are couple of task which we do at our end . Like, Schematic properties update, reading props, getting library information. Cleaing and updating design cache.
View ArticleForum Post: RE: Best uses of TCL scripting
tennywhy Thanks for your response. Have you used the Cadence online support for tcl sampel scripts or using the tcl script pdf guide presnet inside the cadence installed hierachy?
View ArticleForum Post: RE: Not able to start XRUN (Error: No such file or directory)
Hi Alonso, Thanks for the quick reply. The hint to run the 64 bit binary helps a lot. I am modifying the XCELIUM script as follows: export...
View ArticleForum Post: Failed to initialize incremental netlisting (unlock)
Unfortunately, the thread Failed to initialize incremental netlisting is locked, so i cannot answer to this. So i have to open a new discussion to answer to it. I had the same issue (probably using the...
View ArticleForum Post: RE: Failed to initialize incremental netlisting
We lock old threads for two reasons: This helps limit the opportunities for spammers to post junk on old threads It also helps reinforce the principle of keeping discussions separate for different...
View ArticleForum Post: RE: update layout creates a Rectangle "Board Geometry/Top_Room"...
Hi JC, to remove rooms please use menu: Setup > Outline > Room Outline. To setup the board outline you should also invoke the Design Outline setup tool from the setup menu before placing any...
View ArticleForum Post: Dynamic Shape no clearance with other elements
My board has 12 layers. 4 layers of them can't be poured copper correctly. In the normal layer, the copper has correct clearance with pins/clines/vias: While in the abnormal layer, the copper only have...
View ArticleForum Post: RE: DRC on duplicate nets
Can you try using the net names in the Find Window in OrCAD Capture? I have searched NET1 in Find window as shown below it is highlighting the nets present on the schematic page. There is no DRC in...
View ArticleForum Post: RE: Dumping layer list sorted by "swatch" - Solved by using...
Thanks for your help, Andrew, I think I sorted this out: I ended up using the public API. Initially I had syntax errors, which were solved as follows (for whoever is interested in the future): Open the...
View ArticleForum Post: RE: Dynamic Shape no clearance with other elements
Go into the cross section editor and make sure these are not set as negative planes.
View ArticleForum Post: RE: Dynamic Shape no clearance with other elements
Both positive & negative layers showed the same problem, two GND, one PWR and one signal layer.
View ArticleForum Post: RE: Dynamic Shape no clearance with other elements
Just tried created 4 new layers to replace these problematic layers. It is resolved and I don't know why.
View ArticleForum Post: RE: Get level of hierarchy of part
Hi ElecDesigner, I have created a sample script which will print the part hierarchy level with root schematic as well as schematic under which part is placed. Steps to run: 1. Copy the code in notepad...
View ArticleForum Post: RE: Display Your Know How: Placement
B A is too close to the edge and could get bumped during assy de-panelization
View ArticleForum Post: Using text files to define spectre analysis with monteCarlo
In order to run multiple dc analysis within the same spectre run with alter statements inbetween them, I use the "Definition Files" part of the "Simulation Files" form. It works well with regular runs,...
View ArticleForum Post: Tool to create *.lib and *.db files for designs made in Innovus
Hi all, I have made a custom cell in Innovus that I will be instantiating into a bigger block, which I will also be using Innovus to do the Place & Route. I understand that I can generate a *.lef...
View Article