Forum Post: RE: Invalid CDF choice
You know what, I should have checked in a real database, rather than just off the top of my head. I checked in the documentation too. The issue is that "source" is the name of a built-in attribute for...
View ArticleForum Post: RE: Invalid CDF choice
Thanks Andrew, I already tried do find the chapter explaining the attributes, but with no succes. Everything I know is learned with self study, it's a bit hard to search for something if you don't how...
View ArticleForum Post: RE: Suppressing HDL Parser Warning and port mismatch warnings
Hi Andrew, Your suggestions worked perfectly. Thank you! Lawrence, thanks for pointing me in the right direction. I'll make a note of this should I need to do something similar again. Regards, Andrey
View ArticleForum Post: Problem with Sign-off option in EDI
Hello everyone, I'm trying to use the sign-off option available in EDI for optimization and also timing report . Everything goes well till after post route stage, however I somehow trapped in an...
View ArticleForum Post: RE: Problem importing DXF traces
Hi Wild, Thanks for your comments on this, yes I checked it but the problem was that I was deleting everything else on the layout before importing it, I usually do that in Altium to avoid having to...
View ArticleForum Post: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi, I need to simulate the noise of my circuit at specific points in time after transient analysis. For this I use the "ANALYSIS DURING TRAN", (analysis->tran->options-?output->"ANALYSIS...
View ArticleForum Post: RE: Difference in output of calculator 'pvi' function between ADE...
I was able to identify the problem, I believe I had been using different RF/LO frequencies initially, and these were set a global variables in the ADE XL setup. By disabling them, things seem to be...
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Mohit, Which IC version are you using? In IC616 and IC617 (at least the latest ISRs which I have on my laptop) I get this: Regards, Andrew
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Andrew, Thanks for the quick reply. I am also using version 6.1.6-64bit(500.1), so it is strange, but I don't get the similar dialog. Also, if I run an stb or ac at actimes, I can't plot the results...
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Mohit, Because I see this question a lot - and there's quite a bit of confusion around the topic of "transient noise summary", I wanted to bring this up. If you have access to...
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Tawna, Thanks for clarifying a potential confusion in terminology (looks like I don't have access to the support portal). However, I am not running transient noise analysis. I am simply running...
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Mohit, I am able to Results-Print-noise summary when using transient with acnames/actimes. I'm not sure why you aren't able to. You might want to open a Case with Customer Support to look into this....
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
I don't think this is something that has been implemented recently - certainly I didn't find anything that suggested that when I did a search. I'm on a plane so can't test some older versions such as...
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Andrew, From the spectre log, the MMSIM version is: 13.11.176 (Linux). Thanks for helping track this down. Mohit
View ArticleForum Post: RE: Print Noise Summary after "ANALYSIS DURING TRAN"
Hi Tawna, OK thanks for checking. I will look into contacting customer support. Just FYI, I don't have direct knowledge of our license numbers etc., which is taken care by the computing support. Mohit
View ArticleForum Post: RE: OrCAD Capture 16.3 hangs on load
Finally I have moved from OrCAD V16.3 to OrCAD V16.6. I have solved my issue. The OrCAD V16.6 is having amazing update.
View ArticleForum Post: ead_workshop - ade-xl error message (1921)
Hi friends from Cadence, My virtuoso is IC6.1.6.500.13. I have an error with ade-xl,when I use the ead_workshop (Rapid Adoption Kit). The ade-xl error message (1921) is the following: "Failed to start...
View ArticleForum Post: RE: ead_workshop - ade-xl error message (1921)
. . . and, this error appears when I simulate choosing the option "Enable Electrical Data Capture for EAD Flow"
View ArticleForum Post: RE: High Fanout nets synthesis encounter
Hi Kari.. I found out the problem. The power nets haven't routed properly and They haven't declared as special nets too. Now It has been figured out. Thanks.
View ArticleForum Post: SystemVerilog virtuoso netlister
Hi all, I'm using the SystemVerilog netlister in the virtuoso environment(Launch->Plugins->Simulation->SystemVerilog). My aim is to generate a netlist of the analog circuitry modeled in...
View Article